Regular Product
Showing 169–192 of 388 results
-
-
-
-
-
IC's
CD4017 Ic Counter IC (pack of 10)
Ask for Latest offer / Availability : https://bit.ly/2XY2dAi
- High speed 16 pin CMOS Decade counter
- Supports 10 decoded outputs
- Wide supply voltage range from 3V to 15V, typically +5V
- TTL compatible
- Maximum Clock Frequency: 5.5Mhz
- Available in 16-pin PDIP, GDIP, PDSO packages
SKU: n/a -
IC's
CD4020 – 14-Stage Binary/Ripple Counter (Pack of 10)
Ask for Latest offer / Availability : https://bit.ly/3qIlguK
- 14-stage Ripple Carry Binary Counters
- Counters Advance One Count on Negative Transition of Clock Pulse
- Wide Operating Voltage Range
- Operating Temperature to 85oC
- Low Power TTL
SKU: n/a -
IC's
CD4066 – Quad Bilateral Switch (Pack of 10)
Ask for Latest offer / Availability : https://bit.ly/3qFLWwe
- Quad Bilateral Switch for Transmission or Multiplexing Analog or Digital Signals
- Pin for Pin Compatible with the CD4016
- Improved ON Resistance over CD4016
- Operating Temperature to 85oC
- Low Power TTL
SKU: n/a -
-
IC's
CD4511 – BCD to 7-segment Latch/Decoder/Driver (Pack of 10)
Ask for Latest offer / Availability : https://bit.ly/3qIztb4
- Contains a 4-bit Storage Latch, BCD-to-Seven Segment Decoder and Output Drive
- Suitable for LED, Incandescent, Fluorescent or LCD Readouts
- Blanking Input
- Lamp Test Provision
- Low Power TTL
SKU: n/a -
3D Accessories
CM108 Chipset USB 2.0 to 3D Audio Sound Card Adapter Virtual 5.1 CH Sound Track
Ask for Latest offers/availability : https://bit.ly/3uj2pcP
Eliminate the need for a traditional sound card with this USB Sound Adapter. Connect a speaker or headphone directly to the adapter in order to enjoy the virtual 5.1 channel sound track. Get this great adapter without hesitation.
SKU: PGI-550 -
3D Accessories
CNC 3D Printer Mech Endstop Switch For RepRap Makerbot Prusa Mendel RAMPS1.4
Ask for Latest offers/availability : https://bit.ly/3o6LBVv
The mechanical endstop uses a lever switch to detect when it is activated. The switch is wired up so that when activated, it pulls the signal to LOW. There is also an LED on the board that will light up when the switch is activated.It uses a standard 4 pin .100″” pitch header and accepts a standard, old-style CD-ROM audio connector cable. Brand new and high quality. The endstop is a reliable endstop / switch solution for any type of 3D printers and other CNC and/ or 3D tools.
SKU: PGI-0012030 -
3D Accessories
CNC shield v3 engraving machine 3D Printer
Ask for Latest offers/availability : https://bit.ly/3kJmJRJ
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers, CNC. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use. UNO for Arduino module IO port correspondence introduction.
SKU: PGI-0012202 -
-
Prayog Blaster, Water Flow And Level Sensor
DC 3-6 V Mini Micro Submersible Water Pump
Ask for Latest offer / Availability : https://bit.ly/3aXaN9S
- Operating Voltage : 2.5 ~ 6V
- Operating Current : 130 ~ 220mA
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Outlet Outside Diameter: 7.5 mm
- Outlet Inside Diameter: 5 mm
SKU: PGI-00301183 -
Motors | Drivers | Actuators Categories, Plastic Gear Box Motor
DC Motor – 1000RPM – 12Volts
Ask for Latest offer / Availability : https://bit.ly/2U14OuE
- The metal gears have better wear and tear properties.
- The gearbox is sealed and lubricated with lithium grease and requires no maintenance.
- Although motor gives 100 RPM at 12V, the motor runs smoothly from 4V to 12V and gives the wide range of RPM, and torque.
- The shaft has a hole for better coupling.
- Operating Voltage(V): 12
- Rated Torque(kg-cm): 0.5
- Stall Torque(kg-cm): 2.0
SKU: PGI-00141
