Shop
Showing 625–648 of 1946 results
-
Break out Boards
CP2112 debug board USB to I2C Communication Module
Ask for latest offers/availability : https://bit.ly/2Ab0ajP
- On-chip power-on reset circuit, on-chip voltage regulator: 3.45 V output
- Compliant with USB specification 2.0 standard; full speed (12Mbps)
- USB suspend status via SUSPEND and /SUSPEND pins
- Integrated 194-byte one-time programmable ROM for storing customizable product information
SKU: PGI-00617815 -
-
Current and Voltage Sensor
Current and Voltage Detection Module Arduino Compatible
Ask for latest offers/availability : https://bit.ly/3cKcRjw
- Test Voltage range: DC3 – 25V (for Arduino work on 5V) or DC3 – 16.5V (for Arduino work on 3.3V)
- Test Current range: DC0 – 3A PCB
- Size (LxWxH)mm : 22 x 21 x 7
SKU: PGI-00396910 -
Motor Driver
Cytron 10Amp 7V-30V DC Motor Driver for R/C (2 Channel) MDDRC10
Ask for latest offers/availability : https://bit.ly/3u1Pg6R
- Operating Voltage: DC 7 V to 30 V
- Maximum Motor Current: 10 A continuous, 30 A peak
- Motor Output PWM Frequency: 20 kHz
- RC Input Voltage (RC1 & RC2): Low Level: 0-0.7 V | High Level: 1.5-15 V
- Output Maximum Current: 0-500 mA
SKU: PGI-00945382 -
Motor Driver
Cytron 25A DC motor driver with Switch and Potentiometer Control (MD25HV POT)
Ask for Latest offers/availability : https://bit.ly/3ni9Gbx
- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
SKU: PGI-00497900 -
Motor Driver
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
Ask for Latest offers/availability : https://bit.ly/3z3t6my
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 25V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: PGI-002774 -
WIRELESS REMOTE CONTROLLER
Cytron Arduino PS2 Shield
- 5V powered low current consumption.
- Simple to use UART protocol
- Vibrator motor on PS2 is controllable.
- Wired and Wireless PS2 controller is supported.
- PS2 Controller will automatically operate in analog mode.
- A status LED
- Jumper selector to select different UART Baud Rate (9600, 57600, 115200).
- Jumper selectors to select different digital pin as UART TX and RX pin.
SKU: n/a -
Break out Boards
Cytron Breakout USB A Type Male – Good Quality
Ask for latest offers/availability : https://bit.ly/2zrpCS0
- This is a breakout board for USB Connector A-Type. It is pre-soldered with the USB connector. Pins are broken out to 0.1″ for easy mounting on breadboard or donut board. Ideal for USB DIY project.
SKU: PGI-007442 -
Motor Driver
Cytron Dual Channel Enhanced 10 Amp DC Motor Driver 30A Peak MDD10A
Ask for Latest offers/availability : https://bit.ly/3z0ppxZ
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: PGI-003405 -
Motors | Drivers | Actuators Categories
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
Motors | Drivers | Actuators CategoriesCytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
Ask For Availability :- https://bit.ly/2Qe1pow
- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: PGI-002777 -
Arduino
Cytron Maker Drive H-Bridge Motor Driver
- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA) to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
SKU: n/a -
Motor Driver
Cytron Maker Drive H-Bridge Motor Driver
Ask for Latest offers/availability : https://bit.ly/3A0vrjJ
- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA) to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
SKU: PGI-00381588 -
Line Sensor
Cytron Maker Line: Simplifying Line Sensor For Beginner
Ask for latest offers/availability : https://bit.ly/2VPnsTv
- Operating Voltage: DC 3.3V and 5V compatible (With reverse polarity protection).
- Recommended Line Width: 13mm to 30mm.
- Sensor Refresh Rate: 200Hz
- Easy calibration process.
- Supports a wide range of controllers such as Arduino, Raspberry Pi, etc.
SKU: PGI-00718381 -
-
IR And PIR Sensor
Cytron Maker Reflect: Simplifying IR Reflectance Sensor for Beginner
Ask for latest offers/availability : https://bit.ly/2KoDI8T
- Operating Voltage: 3.3V and 5V Compatible
- Sensing Distance (Height): 1mm to 40mm (Vcc = 5V, Blackline on a white surface)
- Features a tiny reflectance sensor
- This sensor is used in line following robot
- Fits easily in the tightest space
SKU: PGI-00718385 -
Motor Driver
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
Ask for Latest offers/availability : https://bit.ly/38Txn1x
- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: PGI-002784 -
Motor Driver
CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)
Ask for Latest offer / Availability :- https://bit.ly/3b7iHKH
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm
SKU: PGI-0029672 -
Motor Driver, Prayog Blaster
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
Ask for Latest offer / Availability : https://bit.ly/3pTZPX6
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: PGI-004565 -
-
Motor Driver
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
Ask for Latest offers/availability : https://bit.ly/3jXDesF
-
DC Brush motor Driver, not for brushless motor
-
Input Voltage (Motor): 7 – 45VDC
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
SKU: PGI-008014 -
-
IC's
DAC0800 – 8-bit D/A Converter (pack of 5)
Ask for Latest offer / Availability : https://bit.ly/3632KWf
- Fast settling output current: 100ns
- Complementary current outputs
- Interface directly with TTL, CMOS, PMOS and others
- 2 quadrant wide range multiplying capability
- Wide power supply range
- Low Power Consumption
SKU: n/a -
-
Circuit Board
Data Logger module Logging Shield data Recorder Shield
- SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card.
- Real-time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for years.
- Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering connectors, circuitry or sensors.
- The onboard 3.3v regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run.
- A dedicated and well-designed data logging shield for Arduino.
SKU: PGI-0012191
