Current and Voltage Sensor
Showing all 13 results
-
Current and Voltage Sensor
20A Range Current Sensor Module ACS712
   Ask for latest offers/availability : https://bit.ly/2YdgLOb
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
SKU: n/a -
Current and Voltage Sensor
30A range Current Sensor Module ACS712
   Ask for latest offers/availability : https://bit.ly/2xLm9NF
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 30A
- Sensitivity: 100mV/A
SKU: n/a -
Current and Voltage Sensor, Prayog Blaster, sensors
5A 12V Overcurrent Protection Sensor Module AC Current Detection Sensor
Current and Voltage Sensor, Prayog Blaster, sensors5A 12V Overcurrent Protection Sensor Module AC Current Detection Sensor
Ask for Latest offer / Availability : https://bit.ly/3iqtS50
LC 5A Over-current protection Sensor module uses a current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current
SKU: PGI-400224 -
Current and Voltage Sensor
5A range Current Sensor Module ACS712
   Ask for latest offers/availability : https://bit.ly/2Y0Odal
- Low-noise analog signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
SKU: n/a -
Current and Voltage Sensor
5A range of single-phase AC current sensor module
   Ask for latest offers/availability : https://bit.ly/2VTjwRL
- Onboard precision microcurrent transformer.
- Onboard sampling resistor.
- The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.
- Rated input current: 5A
- Rated output current: 5mA
- Change: 1000: 1
- The linear range: 0 ~ 10A (100 ohms)
- Linearity: 0.2%
SKU: n/a -
Current and Voltage Sensor
ACS758LCB-050B Hall-Effect-Based Linear Current Sensor IC
   Ask for latest offers/availability : https://bit.ly/3aw4l6h
- Integrated shield greatly reduces capacitive coupling from the current conductor to die due to high dV/dt signals, and prevents offset drift in high-side, high-voltage applications.
- Total output error improvement through gain and offset trim over temperature.
- Small package size, with easy mounting capability.
- Monolithic Hall IC for high reliability.
- Output voltage proportional to AC or DC currents.
- Factory-trimmed for accuracy.
- Extremely stable output offset voltage.
- Nearly zero magnetic hystereses.
SKU: n/a -
Current and Voltage Sensor
CJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
Current and Voltage SensorCJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
   Ask for latest offers/availability : https://bit.ly/2VSsP4t
- 0.1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- 2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power.
SKU: n/a -
Current and Voltage Sensor
Current and Voltage Detection Module Arduino Compatible
   Ask for latest offers/availability : https://bit.ly/3cKcRjw
- Test Voltage range: DC3 – 25V (for Arduino work on 5V) or DC3 – 16.5V (for Arduino work on 3.3V)
- Test Current range: DC0 – 3A PCB
- Size (LxWxH)mm : 22Â x 21 x 7
SKU: n/a -
Current and Voltage Sensor
SCT 013 000 100A Non-Invasive AC Current Sensor Split Core Type Clamp Meter Sensor
Current and Voltage SensorSCT 013 000 100A Non-Invasive AC Current Sensor Split Core Type Clamp Meter Sensor
   Ask for latest offers/availability : https://bit.ly/2S5A5sz
- Input Current : 100A
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
SKU: n/a -
Current and Voltage Sensor
SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A
   Ask for latest offers/availability : https://bit.ly/2VAndNj
- Input Current : 0-30A
- Output Mode: 0-1V @ 30mA
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
Â
SKU: n/a -
Current and Voltage Sensor
SCT-013-060 Non-invasive AC Current Sensor Clamp Sensor 60A
   Ask for latest offers/availability : https://bit.ly/3cGGfqY
- Input current (RMS): 60A.
- Max current: 75A.
- Work temperature: -25℃~+70℃.
- Storage temperature: -30℃~+90℃.
- Work voltage: 660V.
- Frequency range: 50Hz-1KHz.
- Dielectric strength: 3.5KV 50Hz 1min
SKU: n/a -
Current and Voltage Sensor
SparkFun Current Sensor Breakout – ACS723
   Ask for latest offers/availability : https://bit.ly/2x1tkka
- Analog output with bandwidth adjustable to 80kHz.
- Measures DC and AC currents up to 10 mA ~ 5A.
- Full electrical isolation of measured and sensed circuits.
- The version without the op-amp has a base sensitivity of 400mV/A.
SKU: n/a -
Current and Voltage Sensor
Voltage Detection Sensor Module 25V
   Ask for latest offers/availability : https://bit.ly/2VzFGcO
- Voltage input range: DC 0-25V
- Voltage detection range: DC 0.02445V-25V
- Voltage Analog Resolution: 0.00489V
- DC input connector: Terminal cathode connected to VCC, GND negative pole
- Output interface: “+” connect 5/3.3V, “-” connect GND, “s” connect the Arduino AD pins
SKU: n/a