3D Accessories
Showing 1–24 of 83 results
-
3D Accessories
1000mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut
- Lead Screw Material: 304 Stainless Steel.
- Length: 1000mm.
- Diameter: 8mm.
- 4 Start Lead Screw
- Brass Nut Size: 10 x 13 x 22 mm.
- Mainly use for Stepping motor driving guide rail.
- T shape design, made of high-quality stainless steel material.
- Easy to install and convenient to use
SKU: n/a -
3D Accessories
13DOF Biped Robot, Leg Robot Servo Motor Metal Bracket (NO Servo)
- 13DOF Biped Robot, Leg Robot Servo Motor Metal Bracket (NO Servo).
- 2mm thick 60 Series Hard aluminum The lower limbs of the robot can walk straight and turning.
- Upper limbs of the robot can perform a variety of arm movements.
SKU: PG352 -
3D Accessories
3D printer 128×64 Smart LCD controller for ramps 1.4
- RAMPS 1.4 LCD 12864 intelligent controller.
- With an SD card base on back.
- Large screen display 128×64 LCD (3.2″)
- SD card slot at the back, able to directly select a file and print
- The product comes encoder parameter adjustment can be achieved, and the file selection print
- Plug & play on the RAMPS, but need to modify the firmware to support.
- LCD 12864 Smart Controller fully supported by Marlin Firmware.
SKU: n/a -
3D Accessories
3D Printer Controller Board For RAMPS 1.4 REPRAP PRUSA MENDEL
It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega/SainSmart Mega with its powerful platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino Mega/Sainsmart MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
SKU: PG510 -
3D Accessories
3D Printing Pen w/Filament and Power Adapter
Ask For Availability :- https://bit.ly/32uGW0W
- Input Voltage: 100-240 V AC.
- Temp: 160~230 Deg settable.
- Filament: 1.75 mm PLA or ABS.
- This 3D Pen is designed for the freehand drawing of 3-Dimensional objects
- Adjustable output speed, temperature
- Create projects horizontally or vertically
SKU: n/a -
3D Accessories
3DEOMETRY INNOVATIONS NoisyBot 3D Printer
Ask For Availability :- https://bit.ly/2NpMC8e
- Portable
- Low Maintainance
- Build Volume: 180 mm diameter, 250 mm height.
- Layer Resolution: Up to 100 Microns.
- Filament Diameter: 1.75mm.
- Nozzle Diameter: 0.4mm.
- Power Supply: 220V-240V
- Nozzle Temperature: 260 °C.
- Heat Bed: 100 Degrees C.
SKU: n/a -
3D Accessories
5th Gen Prusa i3 Desktop 3D Printer DIY Kit (Unassembled)
Ask For Availability :-https://bit.ly/2pRN2LJ
- AC Input Voltage:Â 100-120VAC/4.8A or 200-240VAC/2.4A
- Layer Resolution: ±0.10mm
- Printing Material:Â PLA, ABS, PVA, PEVA, HIPS
- 3D flatbed printer.
- Acrylic Plate, more stable and durable.
- Support ABS, PLA, PVA, WOOD, and NYLON easy to use.
- Support SD card with LCD for off-line printing (Included with the printer).
- Support Bowden extruder.
SKU: n/a -
3D Accessories
CM108 Chipset USB 2.0 to 3D Audio Sound Card Adapter Virtual 5.1 CH Sound Track
Eliminate the need for a traditional sound card with this USB Sound Adapter. Connect a speaker or headphone directly to the adapter in order to enjoy the virtual 5.1 channel sound track. Get this great adapter without hesitation.
SKU: KG550 -
3D Accessories
CNC 3D Printer Mech Endstop Switch For RepRap Makerbot Prusa Mendel RAMPS1.4
The mechanical endstop uses a lever switch to detect when it is activated. The switch is wired up so that when activated, it pulls the signal to LOW. There is also an LED on the board that will light up when the switch is activated.It uses a standard 4 pin .100″” pitch header and accepts a standard, old-style CD-ROM audio connector cable. Brand new and high quality. The endstop is a reliable endstop / switch solution for any type of 3D printers and other CNC and/ or 3D tools.
SKU: PG426 -
3D Accessories
CNC shield v3 engraving machine 3D Printer
This expansion board as a driver expansion board, can be used for engraving machines, 3D printers, CNC. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors. Very convenient to use. UNO for Arduino module IO port correspondence introduction.
SKU: PG092 -
3D Accessories
DRV8825 stepper motor driver Module arduino 3D printer RAMPS1.4 RepRap StepStick
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- 45 V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3 V and 5 V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- layer, 2 oz copper PCB for improved heat dissipation.
SKU: PG232 -
3D Accessories
Dual H-bridge driver L293D Two DC motor or One Stepper Motor Module
- Â Arduino / Raspberry Pi L293D H-Bridge 4 Channel Dc Motor Control Support Pulse With Modulation
- Tested in Arduino, Raspberry, IOIO & Node MCU
- Input Voltage: DC4.5v – 25V
- Output Current: 600mA Per Channel
- Peak Current: 1.2A Non Repetitive Per Channel Enable Facility
- IC Protection: Auto Shut on High Temperature
SKU: PG363 -
3D Accessories
Dual-H Bridge L293D 4 DC Motor Driver Module Robot 4WD Smart Car
The drive module can directly drive four DC motors, drive the car chassis is 4WD 4 choice .Driving battery big up to 1A generally smart car motor current 100-300MA only four are sufficient to meet the control requirements .While leaving Road stepper motor interface can drive Road five line four-phase stepper motor or Road, two-phase four-wire stepper motor, very suitable for precise control requirements.
SKU: PG364 -
3D Accessories
DUE R3 Board AT91 SAM3X8E ARM 32 Bit 3D Printer Motherboard Main
RAMPS-FD Shield for DUE Board When you use Arduino Due as the controller of your 3D Printer, you may find the RAMPS1.4 is not compatible with DUE.As you know the Arduino Due is a microcontroller board based on the Atmel SAM3X8E ARM Cortex-M3, the importance is the Atmel SAM3X8E chip used on the Due operates at 3.3V,worse applying 5V to the Due’s inputs will likely damage the chip.
SKU: PG331 -
3D Accessories
E3D 12V Volcano Upgrade Kit for 1.75mm with 0.80 mm Nozzle
With E3D 12V Volcano Upgrade Kit for 1.75mm with 0.80 mm Nozzle Print big and fast! TheE3D 12V Volcano Upgrade Kit for 1.75mm with 0.80 mm Nozzle kit is to upgrades your V6 or Aero HotEnd to print bigger, faster, and stronger part
SKU: n/a -
3D Accessories
E3D Brass V6 Nozzle – 1.75mm x 0.40mm
Modify your 3D printer to print fine details or large parts with E3D’s V6 nozzles. These nozzles are fully integrated into the E3D ecosystem of 3D printer parts and are compatible with V6, Lite6, and Titan Aero. Compatible with Prusa 3D printers.
SKU: n/a -
3D Accessories
E3D Brass V6 Nozzle – 1.75mm x 0.50mm
Modify your 3D printer to print fine details or large parts with E3D’s V6 nozzles. These nozzles are fully integrated into the E3D ecosystem of 3D printer parts and are compatible with V6, Lite6, and Titan Aero. Compatible with Prusa 3D printers.
SKU: n/a