Relay

      Ask for latest offers/availability : https://bit.ly/36dK6Kf

1. The module using Songle relay control.
2. AC voltage 250V, AC current 10A, maximum DC voltage 30V DC current maximum 10A.
3. Power indicator (green), Two ways of relay status indicator light (red).
4. Using 8550 transistor-driven, strong driving ability.
5. Has the fixed bolt hole and easy installation.

      Ask for latest offers/availability : https://bit.ly/3cOJ61A

1. 2 channel 2 AMP Solid State Relay board
2. Control 2 loads of up to 2 amps each at 120V or 240V AC.
3. Good for lighting, holiday displays etc.
4. Input control signal voltage:
   1. 0-0.5V the state of low-level relay OFF
   2. 0.5-3.3V Unknown State
   3. 3.3-5V high-level relay ON
5. Operating Voltage: 5V
6. Operating Current: 16mA
7. Maximum Load: 2A @ 240VAC

      Ask for latest offers/availability : https://bit.ly/2zuFLWv

1. Has been assembled, and electrical test passed.
2. Led indicator for each relay.
3. Operating Voltage: 5V
4. Operating Current: 12.5mA
5. Maximum Load: 2A @ 240VAC

      Ask for latest offers/availability : https://bit.ly/3duWgAB

1. 6-way relay output module contact capacity is 10A 250V.
2. input IN1, IN2, IN3, IN4, IN5, IN6 signal, a low level is effective.
3. Using single-chip design, reliable performance, strong anti-interference, no false triggering, superior performance.
4. The trigger terminal has optocoupler isolation, the independent external power supply can trigger completely isolated.
5. Each relay has an activity indicator light. With 4 fixed bolt holes, easy installation.
6. Support all SCM control. It is applicable to the industrial sector, PLC control and home intelligent control.

      Ask for latest offers/availability : https://bit.ly/3clwbEb

1. Low Level Trigger Relay Module
2. Two separate LEDs for On/Off indication of the Relay.
3. Triggering input voltage 3.3V – 5V
4. Two separate LEDs for On/Off indication of the Relay
5. Triggering input voltage 3.3V – 5V 4)
6. Back EMF protection
7. Back EMF protection 2 LEDs to indicate when relays are ON.
8. Works with logic level signals from 3.3V or 5V devices
9. Opto isolation circuitry
10. Module with diode current protection, short response time
11. AC Control Voltage: 250V @max.10A
12. DC Control Voltage: 30V @max. 10A

      Ask for latest offers/availability : https://bit.ly/3fK3Md4

1. Operating voltage: 6-30V
2. Time interval:0.1 s (minimum) ~ 999 min (maximum) continuously adjustable.
3. Trigger Signal Source: High-Level Trigger (3.0 V-24 V)
4. Output Capacity: can control no more than DC 30V 5A AC or 220 V devices 5A
5. Optocoupler Isolation.

      Ask for latest offers/availability : https://bit.ly/35NQjfO

1. Channel: 8 channel
2. Relay Operating Voltage: 5V
3. One normally closed contact and one normally open contact
4. Triode drive, increasing relay coil
5. High impedance controller pin
6. Pull-down circuit for the avoidance of malfunction
7. Power supply indicator and Control indicator lamp
8. Power supply and relay instructions, lit, the disconnect is off;

      Ask for latest offers/availability : https://bit.ly/3cqeWSg

1. Operating Voltage: 12V DC
2. Equipped with high-current relay 10A@250VAC / 10A@30VDC
3. It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
4. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
5. Freewheeling diode to protect your microcontroller
6. Input Signal Pin connected to Burg stick for easy accessibility
7. LED Status indicators to indicate the relay ON/OFF status
8. Mounting holes provided

      Ask for latest offers/availability : https://bit.ly/2zjVIil

1. This is a Single Pole Double Throw(SPDT) type of relay
2. Purposefully designed for RC Applications
3. Max. AC voltage: 250V
4. Max. DC voltage: 30VDC
5. Max current: 10A

      Ask for latest offers/availability : https://bit.ly/3dHwklJ

1. 30mA typical draw from receiver
2. 12-inch servo pigtail
3. Max relay voltage: 240VAC
4. Max relay current: 10A @ 28VDC, 12A @ 120VAC, 10A @ 240VAC.
5. Relay resistance: 100 mΩ max
6. operating voltage: 3.5V to 5.5V (on servo pigtail)