Motor Driver
Showing all 20 results
-
Motor Driver
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: n/a -
Motor Driver
Cytron 25A DC motor driver with Switch and Potentiometer Control (MD25HV POT)
- Bidirectional control for one brushed DC motor.
- Maximum Motor Current: 25A continuous, 60A peak.
- 5V output for the host controller (250mA max).
- Buttons for quick testing.
- PWM frequency up to 40kHz.
- Dual Input Mode: PWM/DIR or Potentiometer/Switch Input.
SKU: n/a -
Motor Driver
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 25V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Motor Driver
Cytron Dual Channel Enhanced 13Amp DC Motor Driver 30A Peak MDD10A
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 13A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Motor Driver
Cytron Maker Drive H-Bridge Motor Driver
- Dual channel, Bi-directional control motor driver
- Support motor voltage from 2.5V to 9.5VDC
- Maximum current up to 1.0A continuous and 1.5A peak (<5 seconds)
- 5V Output (200mA) to power the controller.
- Inputs compatible with 1.8V, 3.3V and 5V logic (Arduino, Raspberry Pi, etc).
- Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
- Regenerative Braking
SKU: n/a -
Motor Driver
Cytron MDS160A SmartDrive160 160AMP Dc Motor Driver (Peak 190Amp)
- Bi-directional control for a single brushed DC motor.
- Support input voltage from 8V to 28V.
- Maximum current up to 190A peak (1 minute), 175A (2 minutes) or 160A (continuously).
- 16 KHz switching frequency for quiet operation.
- LiPo battery low voltage warning.
- Thermal protection.
SKU: n/a -
Motor Driver
CYTRON SMART DRIVE MDDS30 DUAL 30A (80A Peak)
Ask for Latest offer / Availability :- https://bit.ly/3b7iHKH
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm
SKU: n/a -
Motor Driver, Prayog Blaster
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
Ask for Latest offer / Availability : https://bit.ly/3pTZPX6
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: PGI-004565 -
-
Motor Driver
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
-
DC Brush motor Driver, not for brushless motor
-
Input Voltage (Motor): 7 – 45VDC
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
SKU: n/a -
-
-
Motor Driver
Dual Monster Moto Shield VNH2SP30 DC Motor Driver 2x14A (Peak 30A)
Ask for Latest offer / Availability : https://bit.ly/3l8ddVj
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: PGI-28535 -
-
Motor Driver
Leadshine DM542 Digital Stepper Motor Driver
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
SKU: n/a -
-
Motor Driver
Sabertooth Dual 5A Motor Driver for R/C
Ask for Latest offer / Availability :https://bit.ly/36sjUxE
- Operating Voltage(VDC): 6-18
- Peak Current (A): 10
- Continuous Current (A): 5
- No. of Channels: 2
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode-compatible with: 6-12 cell NiMH or NiCd, 2s-4s LiPo, 6V or 12V lead acid (not 18+V lead acid!)
SKU: PGI-4686 -
-
Motor Driver
USB 32Ch Servo Motor Controller Board, support PS2 WIFI with USB Cable
Ask for Latest offer / Availability : https://bit.ly/38ptQsL
- Baud rate (USB): 115200
- Baud rate (bluetooth, UART): 9600
- Storage Flash capacity: 16M
- Mode to choose: 4 types
- Simultaneous controlling servo number: 32 channel
- Max action groups: 256 groups
- Communication agreement: UART
- Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
SKU: n/a