Motors
Showing 1–24 of 130 results
-
Motors
10A Motor Driver Shield – MD10
- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
SKU: n/a -
Motor Driver, Prayog Blaster
10A Motor Driver Shield – MD10
- Bi-directional control of 1 brushed DC motor.
- Support motor voltage ranges from 7V to 25V, .
- Maximum current up to 10A continuous and 15A peak (10 seconds).
- Solid state components provide faster response time and eliminate the wear and tear of a mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
- Speed control PWM frequency up to 10KHz.
- Selectable digital pins for PWM and DIR.
SKU: n/a -
-
-
-
-
-
Geared Motor
12 VOLT, 100 RPM 6 MM SHAFT DC GEAR MOTOR LOW RPM HIGH TORQUE MOTOR
- 100 RPM Centre DC Motor is high quality low cost DC geared motor.It has steel gears
- pinions to ensure longer life and better wear and tear properties.
- The gears are fixed on hardened steel spindles polished to a mirror finish.
- The output shaft rotates in a plastic bushing.
SKU: n/a -
Geared Motor
12 VOLT, 1000 RPM 6 MM SHAFT DC GEAR MOTOR HIGH SPEED MOTOR
- 1000 RPM Center Shaft standard Series DC Motor is high quality low cost DC geared motor.
- It has steel gears and pinions to ensure longer life and better wear and tear properties.
- The gears are fixed on hardened steel spindles polished to a mirror finish.
SKU: n/a -
Non-Geared Motor
1200KV Brushless BLDC Dc Motor – Best use for Drone and Quadcopter
- Stator dia (mm) – 22 Stator length (mm) –
- 13 Stator arms – 12 Magnet Poles – 14
- RPM (kv) – 1200 Idle Current (A) – 0.55/8 Max Current (A) – 17
- Max Power (w) – 190/3 Biggest Thrust (g/s) – 1200/4 Rotor dia (mm) – 28
- Shaft dia (mm) – 3.17 Motor length (mm) – 28 Overall Length (mm) – 42
SKU: n/a -
BO MOTORS
150 Rpm Dual shaft High Quality Low noise Bo Motor 4 pcs + 4 pcs Gripped yellow Bo wheel
- Low density: lightweight, low inertia.
- Capability to absorb shock and vibration as a result of elastic compliance.
- Ability to operate with minimum or no lubrication, due to inherent lubricity.
- The relatively low coefficient of friction.
- Operating Voltage(VDC): 3~12
- Shaft Length (mm): 8.5
- Shaft Diameter (mm): 5.5 (Double D-type)
- No Load Current: 40-180mA.
- Rated Speed(After Reduction): 150 RPM
- Rated Torque: 0.35 Kgcm
SKU: n/a -
Motors
150 RPM Dual Shaft Straight Plastic Gear BO Motor for Arduino/Raspberry-Pi/Robotics
- 150 RPM Dual Shaft Straight Plastic Gear BO Motor
- For Arduino/Raspberry-Pi/Robotics
- Gear materials: plastic
- Motor types: Permanent Magnet
- Brush-type: Brushed
- Magnet types: Ferrite Magnets
- Torque multiplication: Generates a large force at a low speed
SKU: n/a -
Motors
150 RPM Single Shaft Straight Plastic Gear BO Motor
- DIY Projects.
- Battery-operated toys.
- Disk drives Steel rolling mills Paper.
- Machines Medical equipment.
- Radio-controlled aircraft.
- Automobiles Drive systems Positioning.
- Industrial and consumer actuators Winches Robotics Mixers.
- Robotic projects.
SKU: n/a -
SERVO MOTORS AND ACCESSORIES
16-Channel 12-bit PWM/Servo Driver – I2C interface – PCA9685
- Operating voltage: 2.3V to 5.5V
- 5.5V tolerant inputs
- Can operate at minus 40 degrees Celsius to 85 degrees Celsius
- Software reset feature (SWRST Call) allows the device via I2C bus reset
- 25MHz internal oscillator requires no external components
- The maximum allowable 50MHz external clock input
SKU: n/a -
Motor Driver
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: n/a -
Servo Motor
20 KG High Torque MOTOR,Servo Gear Motor for Robo Competition and Fighting Robot
- Net Weight: Approx 62g
Dimension: Approx 40.5 x 20.2 x 38mm
Output gear:25T - Working frequence: 1520μs / 330hz
- Stall torque:17.25kg/cm(4.8v); 20.32kg/cm(6.0v)
Operating speed: 0.18 sec/60° (4.8v); 0.16sec/60degree (6.0v)
Control Angle: 180° degree
Operating voltage: 4.8-6.0v
Gear Type: All Metal gears
Bearing: 2BB (2 ball bearings)
Temperature range: -10- 50deg
Dead band width: 2us
servo wire length: 25cm / 9.84inch
Servo Plug: JR (Fits JR and Futaba)
SKU: n/a - Net Weight: Approx 62g
-